Page 10 of 10 FirstFirst ... 8910
Results 136 to 146 of 146

Thread: Just bought new 2009 sportcity 250

  1. #136
    apriliaforum Member
    Join Date
    Jul 2013
    Location
    Fresno Ca
    Posts
    202
    ya synthetic , but this happened after I put on the rear tire so I figure it has something to do with that. only 30k miles.

  2. #137
    apriliaforum expert
    Join Date
    Apr 2011
    Location
    Clearwater, Fl
    Posts
    7,269
    Did you potentially get the spacers etc out of order and now have the rear wheel binding the brakes?

    Any odors from the rear wheel after riding for a bit? An infrared thermometer can sometimes help pinpoint binding by the heat it causes.


    Here's and example of how handy an infrared thermometer can be as a diagnostic tool:

    My brother had a hot electronics smell in his house that was intermittent so by the time it was noticeable the cause had stopped making it difficult to pinpoint. Standing in the middle of the room with an infrared thermometer in his hand and waving it around showed him higher temps coming from a wall with a closet on the other side which had a breaker box in the back of it. The breaker for the clothes dryer was getting hot where it contacted the busbar even though it was not obvious when you opened the door. By the time it got hot enough to make an obvious smell the dryer had finished its cycle and it was already cooling down. Being Florida the closet has a fully louvered door so the smell was not really concentrated in the closet making it harder to pinpoint especially after the dryer had already finished its cycle and shut off. The busbar was damaged badly enough that when the breaker was replaced they had to put it into another location in the panel. They will be coming back to replace that main panel and relocate it so its no longer in a closet meeting the current building code. The panel is over 50 years old now so it had a good long run.

  3. #138
    apriliaforum Member
    Join Date
    Jul 2013
    Location
    Fresno Ca
    Posts
    202
    The wheel spins freely while i have the bike on and warming up before a ride. Though I did just realize that the belt/rollers are due to be changed out now. I need to look at the valves as well.

  4. #139
    apriliaforum Member
    Join Date
    Jun 2016
    Location
    Florida
    Posts
    235
    Quote Originally Posted by Fresno View Post
    I tend to keep my tires at max psi. I don't know what else would keep the bike limited. When cycle gear put on the rear tire, they mentioned that they didn't have the adapter to fit my tire on the balancer so they didn't end up balancing the tire. Perhaps an unbalanced rear tire is adding to it.
    cycle gear doesn't have cones? Real simple to do scooter rims. Put 1 cone through and turn the other one around to center it. But I'm guessing the genii at CG couldn't come up with a solution.

  5. #140
    apriliaforum expert
    Join Date
    Apr 2011
    Location
    Clearwater, Fl
    Posts
    7,269
    Yes dot the I's and cross those T's as far as valve and CVT maintenance go. Don't overlook regular CVT filter cleanings too. I will clean it every 2,000 to 3,000 miles and after any long ride where its particularly dusty/sandy such as shore line or country back roads. A clean cool CVT is a happy one.

  6. #141
    apriliaforum Member
    Join Date
    Jul 2013
    Location
    Fresno Ca
    Posts
    202
    So I am working my way to take off the transmission cover. I managed to remove 2 air filter bolts on the bottom of the air filter box which allows me to move the air filter box up and out of the way somewhat.

    Then I start on removing the transmission cover bolts. I notice some oil dropping on the floor and its coming from the bolt area right below the oil fill plug. So my question is ; I am assuming I need to dump out the oil before taking off the transmission cover ? I put the bolt back and the oil stopped seeping out.

    Edit: yeah I'm watching the video now and He (Robot ) does drain the oil before cracking open the belt cover. Watching the vespa videos really help, I see where I took out the wrong bolts so I fixed that.

    Also doing valves for the first time. I have it so the feeler gauge drags on the valves lightly. My valves were actually about 4k miles past due so they were too tight to fit the feelers through. I suspect that could be the reason for loss of the top end.
    Last edited by Fresno; 11-06-2017 at 07:40 PM.

  7. #142
    apriliaforum prov-nov Pinkscoot's Avatar
    Join Date
    Aug 2016
    Location
    NC
    Posts
    30
    While dropping the engine on my BV250 I had to remove one of the oil sump bolts and with out thinking I left it loose an found a small puddle the next day. You need to look carefully when pulling the CVT cover and see where it ends and the sump begins. The oil was black and thin so I doubt the previous owner had drained it for a while.

  8. #143
    apriliaforum expert
    Join Date
    Apr 2011
    Location
    Clearwater, Fl
    Posts
    7,269
    You do not remove the oil sump bolts to remove the CVT cover. They usually drain the oil since the belt change interval coincides with the second scheduled regular oil change. No bolts get removed directly below the oil fill or finned area or you could end up damaging the oil sump gasket. There is a check valve spring in the sump cover which you need to be careful of too. If you accidently remove one of the sump bolts be sure to use a torque wrench and tighten them evenly to spec.

  9. #144
    apriliaforum prov-nov Pinkscoot's Avatar
    Join Date
    Aug 2016
    Location
    NC
    Posts
    30
    One of the brake line supports on The BV250 is held on by one of the sump bolts. Since I was removing the engine I pulled that bolt to disconnect the brake, my mistake was not tightening it back up.

  10. #145
    apriliaforum Member
    Join Date
    Jul 2013
    Location
    Fresno Ca
    Posts
    202
    Well I managed to remove all the sump bolts but not the sump itself. The sump itself never moved. I put those bolts back in, I imagine it is 8 fLbs torque on those.

    I did run into the black shield on the left side that has those bolts that spin freely because the nuts on the otherside are not secured. I removed the black shield completely. The black shield has 3 or 4 bolts and it is also zip tied from the factory to a bundle of wires. I imagine if the shield needs to be there ..I can secure with just the zip tie but I don't see myself re-installing it. Perhaps I can use a dremal to trim the shield so it doesn't interfere with the belt cover and then just zip tie it in place to protect wiring from the elements.

    I popped off the belt cover and inside is literally caked with black dust everywhere.
    6 months ago I called my local Aprillia shop in Portland about taking a look at the clutch. About fixing the stutter when starting off from park. The guy on the phone said removing the belt cover is a 3 hour job with labor rate of 100/hour. So essentially popping off the cover is 300.

    Good news is I can just order the new parts , clean up the belt compartment and its good as new.
    Bad news is I hope I didn't harm the exhaust valves by losing track of the interval. I hope I caught it in time. I am about 3k miles past due.

    1st time doing valves. I guess how Robot mentioned it is to slide the feeler into the valve gap and then turn the set screw until it stops and then tighten the nut.
    Last edited by Fresno; 11-07-2017 at 09:11 PM.

  11. #146
    apriliaforum expert
    Join Date
    Apr 2011
    Location
    Clearwater, Fl
    Posts
    7,269
    Quote Originally Posted by Fresno View Post
    Well I managed to remove all the sump bolts but not the sump itself. The sump itself never moved. I put those bolts back in, I imagine it is 8 fLbs torque on those.

    I did run into the black shield on the left side that has those bolts that spin freely because the nuts on the otherside are not secured. I removed the black shield completely. The black shield has 3 or 4 bolts and it is also zip tied from the factory to a bundle of wires. I imagine if the shield needs to be there ..I can secure with just the zip tie but I don't see myself re-installing it. Perhaps I can use a dremal to trim the shield so it doesn't interfere with the belt cover and then just zip tie it in place to protect wiring from the elements.

    I popped off the belt cover and inside is literally caked with black dust everywhere.
    6 months ago I called my local Aprillia shop in Portland about taking a look at the clutch. About fixing the stutter when starting off from park. The guy on the phone said removing the belt cover is a 3 hour job with labor rate of 100/hour. So essentially popping off the cover is 300.

    Good news is I can just order the new parts , clean up the belt compartment and its good as new.
    Bad news is I hope I didn't harm the exhaust valves by losing track of the interval. I hope I caught it in time. I am about 3k miles past due.

    1st time doing valves. I guess how Robot mentioned it is to slide the feeler into the valve gap and then turn the set screw until it stops and then tighten the nut.
    Feeler gauge not quite stops but you can just feel it dragging. A slightly loose valve is a happy valve while too tight can become a burnt and cracked valve.

    Most just carefully trim back the black shield with a utility knife so they never have to remove it.

Page 10 of 10 FirstFirst ... 8910

Similar Threads

  1. New 2009 Sportcity 250 cu3e silver
    By iscoot250 in forum Aprilia and Piaggio 150cc-350cc
    Replies: 28
    Last Post: 09-03-2011, 02:05 PM
  2. I just bought a 2009 RS125 <TRACK TOOL>
    By Phase3 in forum 2009 RS125-USA
    Replies: 3
    Last Post: 04-01-2011, 06:19 AM
  3. just bought new suspension
    By atlantaM3 in forum RSVR and RSVR Factory (2004-2009)
    Replies: 3
    Last Post: 07-10-2010, 09:04 PM
  4. 2009 Sportcity 250 Fender Elimination
    By scooterman in forum Aprilia and Piaggio 150cc-350cc
    Replies: 0
    Last Post: 06-05-2010, 03:23 PM
  5. got a 2009 Sportcity 250
    By wildlife9000 in forum Aprilia and Piaggio 150cc-350cc
    Replies: 14
    Last Post: 08-27-2009, 02:30 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •