PDA

View Full Version : hp guess!


kezajones
08-01-2006, 12:41 PM
right i have just fitted a race am6 engine into my supermoto project with the following specs

Mk prorace 70cc (flowed and ported)
MK prorace 70cc crank
MRD gearbox
Mk limited editon pro race 70 pipe (modified by ummm..... i cant remember lol)
flowed 28mm intake manifold and matching flowed reed block
pvl inner rotor ignition (no lights)
MK clutch kit
Mk primary drive kit
15/48 gearing

power band starts at rougly 14500 and hits a brick wall at 16000
any guess on the power output?, it mussed be a bit because i can wheelie it through 1st and 2nd with the 15/48 gearing!!!!

cheers
RS_Patrick
08-01-2006, 12:55 PM
17,5 HP?

Btw, That it has no more power at all over 16000 Rpm is because even the stiffest reeds start to float at +-16000 Rpm
samRS
08-01-2006, 01:22 PM
nice :burnout:

i bet thats fun to ride! get some pics up what supermoto is it?
kezajones
08-01-2006, 01:27 PM
its a malaguti xsm but with dt50r side pannels a metalic blue spray job with white number boards and im contemplating a yz graphics kit as it only takes a bit of triming.

will post photos when its finished :)
kezajones
08-01-2006, 02:39 PM
what can i do to bump it up some more? :)
Tybersk8er
08-01-2006, 06:52 PM
what can i do to bump it up some more? :)

Be sure that you replace the stock 5mm yellow powerbands with racing 25mm pink top prefomances powerbands. That should have been done first imo. I don't know why so many people wait to do that last. Just by swaping the powerbands you can get a good 3-4 bhp even on a stock rs50. And plus its free!
Charles
08-02-2006, 07:10 AM
Be sure that you replace the stock 5mm yellow powerbands with racing 25mm pink top prefomances powerbands. That should have been done first imo. I don't know why so many people wait to do that last. Just by swaping the powerbands you can get a good 3-4 bhp even on a stock rs50. And plus its free!

RITE!:happy: :rolleyes: :bs:
oribaka
08-02-2006, 07:17 AM
If you want more power, isn't there a way to elminate the reed valves?
RS_Patrick
08-02-2006, 10:17 AM
If you want more power, isn't there a way to elminate the reed valves?

Yeah, glue them shut. :kidding:

Reeds are perfectly ok till 15000+rpm, Just need to find the right stiffnes for them.
kezajones
08-02-2006, 10:18 AM
Be sure that you replace the stock 5mm yellow powerbands with racing 25mm pink top prefomances powerbands. That should have been done first imo. I don't know why so many people wait to do that last. Just by swaping the powerbands you can get a good 3-4 bhp even on a stock rs50. And plus its free!

BAH i have 45mm rainbow neon barbie super pooper scooper dual power bands.
Charles
08-02-2006, 10:24 AM
BAH i have 45mm rainbow neon barbie super pooper scooper dual power bands.

how special are we! i mean, you!":happy:
samRS
08-02-2006, 10:24 AM
BAH i have 45mm rainbow neon barbie super pooper scooper dual power bands.

omg those are so rear how did you get hold of those
Ärräksä
08-02-2006, 11:00 AM
What carb have you installed and with what main jet? It only says about 28mm intake so I'm guessin dellorto?
kezajones
08-02-2006, 12:31 PM
Keihin pwk 28mm (well its a replica by MRD)

120 main,needle on the 3rd clip and a pair of tights for the airfliter :)
Ärräksä
08-02-2006, 01:45 PM
Post couple of pics or make a thread about your project? That would be nice. Haven't seem them in here for a while.
kezajones
08-02-2006, 01:49 PM
will probly do that tomorrow mate:).