PDA

View Full Version : MONSONS GARAGE SALE



monson708
02-25-2003, 10:46 PM
i have 8 316 pistons new in the box $130.00 each,10 sets of 316 rings $10.00 a set,2 rs250 radiators one is a little beat up on the water elbo but still works fine $75.00,the other is good $120.1 brand new 316 cylinder w/ power valves $600.00.1 complete body two peice upper/lower multi tech stock tail and tank $550.00 its yellow&blue,1 set of 2002 forks done by traxxion dynamics w/triple clamps $750.00.wire harness.i got a lot you guys get first crack,then it goes on ebay.

250hillis
02-25-2003, 11:20 PM
Is this parts from the bike I saw at North Florida a few weeks ago? The guy said you raced for him or somehting like that. He had a grey trailer.

monson708
02-26-2003, 08:51 AM
no,that was my sponsor from 2002.that is his personal bike.he sure is a nice guy,did you talk to him much?did the new kid ,jessie look real fast?

250hillis
02-26-2003, 12:09 PM
They didnt ride because it was raining so hard. There we only 5 guys riding all day. He showed up and said I think i will wait until tomm. and left. Super nice guy though.

discopygmy
02-27-2003, 02:08 PM
Monson - I'm interested in the good radiator if it is still available.

- disco

monson708
02-27-2003, 06:54 PM
yep,still got it.$120.00

discopygmy
02-28-2003, 01:38 PM
great - send me an email (rooster_x@yahoo.com) to work out the details.

-disco.

foxster
03-01-2003, 11:38 AM
Monson, you have a fuel tank for sale? What year was that and how much?

Don

monson708
03-01-2003, 06:16 PM
i got a 99 tank and a 2002 tank.my e mail is jmonson2@new.rr.com.

monson708
03-04-2003, 06:32 PM
i just put a ton of stuff on ebay.stock & 316cc

monson708
03-04-2003, 06:48 PM
is anyone interested in a 1999 rs 250 frame/swing arm,sub fame,wire harness,cdi box,power valve control box,P.V. control motor?i have the worlds supply of stuff.i am parting out 3 complete bikes.i got this whole week off,lets do deals and get this stuff out of my basement!

haze2k
03-04-2003, 08:24 PM
Hi, do you have a Crank that would fit a 98 RS engine or a con-rod?

monson708
03-04-2003, 09:00 PM
yes i have a crank that is lightly used,approx. 500 miles.it is trued & welded $350.00.let me know this stuff is going fast.

ecumike
03-04-2003, 09:48 PM
Monson.. you happen to have a PV cable I could get from you?

monson708
03-04-2003, 10:17 PM
yes,what one do you need?i can give you a whole set for $20.00.

ecumike
03-04-2003, 10:26 PM
I need the bottom/right pulley, the lower cable. A set = both cables for 1 pulley? Yea, I'll take em.

See my thread below... "PV Cable lug gets chewed up, any tips for fix/help? ".. that's what happened.

I'll email you offline.

Haze2k
03-05-2003, 09:13 PM
Ok sounds cool but I have to ask a dumb question..... What does trued and welded meen?my bike is just the stock not 316cc if it will fit thats cool and I will mail you.

monson708
03-05-2003, 09:38 PM
trued means the crank is straight.the rs 250 crank has a tendency to walk on the mag. end so i weld all the pins.the crank is the same but you need to remove the small washers from the wrist pin cause the thrust surface is changed to the big end of the con rod.it will be self explanitory when you see it.e mail me directly jmonson2@new.rr.com.

ecumike
03-05-2003, 11:59 PM
Monson.. you get my email?

wsmc667
03-06-2003, 12:05 AM
yo monson, please e-mail me ... to -> monson@ducatitech.com

thanks,
chris

monson708
03-06-2003, 10:02 AM
i need your address to send the cables.you can send the $20.00 when you get the parts + shipping.i trust you.

ecumike
03-06-2003, 10:17 PM
You've got mail

monson708
03-08-2003, 08:34 AM
its all got to go!!! frames,swing arms,forks,triple clamps,rear sub frames,complete engines,crank case w/ trans. ,name your price im sick of looking at this stuff.+ i just got the kawasaki kit parts list for my new bike and i want it ALL!!!

jmonson2@new.rr.com

Duc995
03-08-2003, 01:05 PM
Hey...I thought you said the BB pistons retailed at $180 and you were looking to sell them for $130 each? I just checked my receipt and they were $119 each from Mototek. FYI:eek:

monson708
03-08-2003, 09:27 PM
yea,he messed up & was selling them for a loss.i have my bill fight here and it cost me $900.00 to get ten cut & coated.the pistons cost $21.00 each & rings cost $11.00 a set.+ you have to ship them twice so you do the math.im looking to get my money back,not make extra.

RegganiRS250
03-11-2003, 12:37 PM
Monson, do you have one of the plastic mounts for holding the splitter box and power valve pulley, it mounts on both sides of the inside of the frame. Also do you have any more sets of power valve pulley cables to get rid of?

monson708
03-12-2003, 10:30 PM
yes to both.i would say $20.00 for a set of cables $20.00 for the bracket.

RegganiRS250
03-26-2003, 03:55 PM
Hey Monson, do you have any sets of forks left? How much?

monson708
03-26-2003, 08:09 PM
sorry i just sold them 20 min. ago.

blsexton
04-19-2003, 04:52 PM
i need spares for track days- looking to buy oem or aftermarket rearsets and clip ons and shift lever/brake lever and shift rod please email prices to bls72bmw@yahoo.com 02 250 RS

dutchieindublin
05-06-2003, 06:18 AM
Monson,

Do you have anything left?

bkjar
05-06-2003, 12:13 PM
Jim,
Please send me a list of all the stuff you have left.
Thanks,
Brian Kjar
New York